P1811 - E.T.

ND Pipes · Post by **ND Pipes** » Tue Jun 14, 2011 6:17 am

jubilarka
P1811 - E.T. (Extra-Terrestrial)
more pic's here: http://tnd-pipes.com/pipes/p1811-e-t-extra-terrestrial/

W.Pastuch · Post by **W.Pastuch** » Tue Jun 14, 2011 6:59 am

Great! I'm really loving this shape! There's a lot going on in this pipe and it all holds together really nicely. I love the grooves on the bottom of the shank! The only part that my unexperienced eye doesn't fully like is the shank application, maybe you could have made the rings at an angle that would match the rings on the bowl...?
Anyway, great pipe!

ND Pipes · Post by **ND Pipes** » Tue Jun 14, 2011 7:10 am

keilwerth wrote:Great! I'm really loving this shape! There's a lot going on in this pipe and it all holds together really nicely. I love the grooves on the bottom of the shank! The only part that my unexperienced eye doesn't fully like is the shank application, maybe you could have made the rings at an angle that would match the rings on the bowl...?
Anyway, great pipe!

i understand what you are thinking of but, if i did that it will be in confrontation with the shank itself - it is risky to make the ring at an angle other than 90° towards the lines of the shank... the angle of the ring is there together with the shank, not the bowl itself - and when compared to the shank it is aligned properly IMHO...

taharris · Post by **taharris** » Tue Jun 14, 2011 12:09 pm

Gorgeous. I wouldn't change a thing.

I wish I had your creativity.

ND Pipes · Post by **ND Pipes** » Tue Jun 14, 2011 12:23 pm

thank you man!!

jogilli · Post by **jogilli** » Tue Jun 14, 2011 1:31 pm

tNd

I like it.... it's a little busy but very nicely executed.. there seems to be a small gap where the ring is at before the olive wood, but the glue you used covered it nicely to a point where it isn't really noticable

nicely done

james

ND Pipes · Post by **ND Pipes** » Tue Jun 14, 2011 4:32 pm

jogilli wrote:tNd

I like it.... it's a little busy but very nicely executed.. there seems to be a small gap where the ring is at before the olive wood, but the glue you used covered it nicely to a point where it isn't really noticable

nicely done

james

James - thank you for your reply ...
the gap between the ring and olive wood extension isn't there for sure - only the line of glue that i usually leave there (don't like to press to hard between materials) and is even and well distributed...
i used Forstner bit to make the olive wood flat on that side and also on the other too (before sanding the part towards the mouhtpiece) and the ring is made using a 2mm acrylic plate - so it is also perfectly flat no doubt in that.. glue can be seen, i can confirm that but from what i can see it is evenly distributed as it should be... so, i can't find faults there

...

R.H. · Post by **R.H.** » Tue Jun 14, 2011 5:41 pm

I love your work, so detailed and clean.
IMHO the olivewood extension match perfectly with natural briar.
Your pipes look crazy and stunning at a time, it's great.

ND Pipes · Post by **ND Pipes** » Tue Jun 14, 2011 6:15 pm

Ramon - thank You so much

means a lot to me...
regards
daniel

Boekweg · Post by **Boekweg** » Tue Jun 14, 2011 6:26 pm

@tNd
Very nice!
I always look foreword to your next creation.
I love your style!

wdteipen · Post by **wdteipen** » Tue Jun 14, 2011 8:36 pm

Very cool, Daniel. I think it's generally preferred to not have a glue line with shank adornments. That being said, in this application it really makes the white acrylic band pop as if you had two uber thin rings of black on each side. The only other thing that I think could be improved is the bead on the stem. You've rounded it off while the rest of the pipe has sharper beads and lines. It doesn't look bad but, IMHO, would look even better with a bead that compliments the design on the end of the shank. Very, very nice piece. Bravo!

Wayne

ND Pipes · Post by **ND Pipes** » Wed Jun 15, 2011 12:43 am

thank you guys...
interesting comment Wayne - will have to think about it - thanks for pointing that out ..

best regards
daniel

baronstrasil · Post by **baronstrasil** » Wed Jun 15, 2011 5:53 am

excellent work! I love the pipes with non-standard shape. Very nice pipe

ND Pipes · Post by **ND Pipes** » Wed Jun 15, 2011 5:59 am

thank You dear Sir...

Mike Messer · Post by **Mike Messer** » Wed Jun 15, 2011 11:09 am

I do see some Walle influence in this one, but I would not consider it to be copying him. It's your own work. No doubt, and a most excellent pipe.

ND Pipes · Post by **ND Pipes** » Wed Jun 15, 2011 4:23 pm

thank you Mike - glad you like it...
regards
daniel

Alden · Post by **Alden** » Wed Jun 15, 2011 6:29 pm

This is why I like looking at your pipes !
I won't say that every one of your pipes is my style, but this one really speaks to me.
Beautiful execution, and all of the elements seem to balance very well.
A very impressive shape, very busy but with lots of harmony.
Did I mention I like it

ND Pipes · Post by **ND Pipes** » Thu Jun 16, 2011 1:09 am

...
thank you Edward... it's nice to hear that

regards

Charl · Post by **Charl** » Wed Jun 29, 2011 2:45 pm

This one works for me, congrats!
The stem can use a bit more definition, in my rookie eyes.
But again, well done!

Boekweg · Post by **Boekweg** » Thu Jun 30, 2011 1:12 am

Very nice!
I love your style and creativeness.

pipemakersforum.com

P1811 - E.T.

P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.

Re: P1811 - E.T.