need some help with cutter for bent classics on lathe
-
- Posts: 167
- Joined: Mon Jun 11, 2007 6:20 am
- Location: new jersey
- Contact:
need some help with cutter for bent classics on lathe
Hi Guys,
hope everyone had a nice summer. I am working on upgrading my cutters on my lathe. I know most of you guys make your own. My question is what is the best angle and cutter to get far down on a bent pipe? I experimented a little, but did not want to mess up this really nice block! if someone could help me a little that would be great. looking forward to seeing some of you at the corps show!!
best,
Tim
hope everyone had a nice summer. I am working on upgrading my cutters on my lathe. I know most of you guys make your own. My question is what is the best angle and cutter to get far down on a bent pipe? I experimented a little, but did not want to mess up this really nice block! if someone could help me a little that would be great. looking forward to seeing some of you at the corps show!!
best,
Tim
Re: need some help with cutter for bent classics on lathe
I take it you're using a metal lathe? This is one reason why I prefer shaping on a wood lathe. I was never any good at the Etch-a-Sketch. I use a parting tool to cut my bowl closer towards the shank on bent pipes.
Re: need some help with cutter for bent classics on lathe
I've never seen anyone use the Etch-A-Sketch method to shape a pipe on a metal lathe. You use the same method as on a wood lathe: Lock something in your tool post and use it as a tool rest while you use wood lathe tools to shape.wdteipen wrote:I take it you're using a metal lathe? This is one reason why I prefer shaping on a wood lathe. I was never any good at the Etch-a-Sketch. I use a parting tool to cut my bowl closer towards the shank on bent pipes.
Tim, you just can't get that close to the shank shaping a bent pipe. There's no special tool to do this. You just get as close as you can and go from there by hand.
Rad
- baweaverpipes
- The Awesomer
- Posts: 947
- Joined: Tue Dec 19, 2006 8:07 am
- Location: Franklin, Tennessee
- Contact:
Re: need some help with cutter for bent classics on lathe
Take the top part to where you feel comfortable and the shapes beginnings. The rest is hand work on the wheel.
It's similar to doing a billiard, take the first 1/3 of the bowl definition and shape from there.
Please smite me, Rod Davies is right, get close and go from there.
Your friendly hillbilly,
Bubba
It's similar to doing a billiard, take the first 1/3 of the bowl definition and shape from there.
Please smite me, Rod Davies is right, get close and go from there.
Your friendly hillbilly,
Bubba
Re: need some help with cutter for bent classics on lathe
*working up mana flow for a parful smiting*
ALL YOUR PIPE ARE BELONG TO US!
Re: need some help with cutter for bent classics on lathe
I think Sas may be inebriated....
Andrew
www.andrewstaplespipes.com
www.andrewstaplespipes.com
Re: need some help with cutter for bent classics on lathe
Sorry to disagree with Rad here, i know how he hates that but i do use the etch a sketch method for shaping my pipes. For ages I never had any wood turning tools so i just learnt to do it with the hand wheels, by the time i finally got some proper tools I was used to doing it the other way so i stuck with it. If I had to start over though I think i would recommend learning to di with with wood turning tools, probably easier to pick and use in the long run.
-
- Posts: 167
- Joined: Mon Jun 11, 2007 6:20 am
- Location: new jersey
- Contact:
Re: need some help with cutter for bent classics on lathe
thanks guys funny bruce I know i can't get as far down as a straight. Chris what tools are you talking about?
thanks everyone
thanks everyone
Re: need some help with cutter for bent classics on lathe
Like I said, I've never seen anybody do it.caskwith wrote:Sorry to disagree with Rad here, i know how he hates that but i do use the etch a sketch method for shaping my pipes. For ages I never had any wood turning tools so i just learnt to do it with the hand wheels, by the time i finally got some proper tools I was used to doing it the other way so i stuck with it. If I had to start over though I think i would recommend learning to di with with wood turning tools, probably easier to pick and use in the long run.
Don't disagree with me again. I know some people.
What is a "partful smiting"?
Rad
- archaggelosmichail
- Posts: 188
- Joined: Thu Jul 14, 2011 11:11 am
- Location: Paros, Greece
- Contact:
Re: need some help with cutter for bent classics on lathe
wdteipen wrote:I take it you're using a metal lathe? This is one reason why I prefer shaping on a wood lathe. I was never any good at the Etch-a-Sketch. I use a parting tool to cut my bowl closer towards the shank on bent pipes.
Thats what I suggest, too.
Buy a wood lathe parting tool, and learn how to use it, it will help you almost in every pipe shape.
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Re: need some help with cutter for bent classics on lathe
I'll use a parting tool from time to time, but a skew chisel it my primary tool in shaping pipe bowls on a lathe. I also use a 1/4" bowl gouge a lot.
You might have to experiment to see what method or tool works best for you.
You might have to experiment to see what method or tool works best for you.
Re: need some help with cutter for bent classics on lathe
I've seen one other pipemaker other than Chris shape on a metal lathe using the Etch-A-Sketch method. I think it depends on one's background. Most of us probably start with woodworking on a wood lathe but some pipe makers have more experience on a metal lathe and are pretty good at using the dials. It's probably true that they are rare but I've seen at least one do it and do it pretty well.
Oh, and the parting tool I use is a 1/16" one for shaping the bowl close to the shank, approaching the pipe from the end like you would hollowing a bowl.
Oh, and the parting tool I use is a 1/16" one for shaping the bowl close to the shank, approaching the pipe from the end like you would hollowing a bowl.
- SimeonTurner
- Site Supporter
- Posts: 750
- Joined: Wed Dec 24, 2008 7:46 pm
- Location: Denver, Colorado
- Contact:
Re: need some help with cutter for bent classics on lathe
I frequently cut steps in the bowl using the metal lathe's cutting tools. Similar to using a parting tool, but sometimes faster. I think it's really just a matter of "do whatever works"
Desirous for this to assist
Desirous for this to assist
"It is noble to be good; it is still nobler to teach others to be good - and less trouble."
Turner Pipes Website:
http://www.turnerpipes.com
Of Briar and Ashes:
http://turnerpipes.wordpress.com
Turner Pipes Website:
http://www.turnerpipes.com
Of Briar and Ashes:
http://turnerpipes.wordpress.com
Re: need some help with cutter for bent classics on lathe
Picture worth a thousand words.
It's just a head-on approach with the tool of choice.
It's just a head-on approach with the tool of choice.
ALL YOUR PIPE ARE BELONG TO US!
-
- Posts: 1346
- Joined: Tue Jan 10, 2012 4:55 pm
- Contact:
Re: need some help with cutter for bent classics on lathe
Hey that's some potentially nice grain there Sas! I didn't know your pipes ever HAD nice grain...