Squaring mortise and tenon during freehand drilling
Squaring mortise and tenon during freehand drilling
Hello everyone and Happy New Year
New Year's Eve I tried to shape first dill after. I was very satisfied with the shape and I can see why many carvers prefer the freedom they have, without worrying about where the holes are. However, I messed up the whole thing, because I could not square the mortise hole.
Any suggestion on how to do this phase correctly?
I bow my head to those that can perform this task without any alterations afterwards.
New Year's Eve I tried to shape first dill after. I was very satisfied with the shape and I can see why many carvers prefer the freedom they have, without worrying about where the holes are. However, I messed up the whole thing, because I could not square the mortise hole.
Any suggestion on how to do this phase correctly?
I bow my head to those that can perform this task without any alterations afterwards.
All the best,
Tano
Tano
If you mean aligning the hole with the shank, that is done by establishing lines of "longitude" that cross at the front of the pipe, where a center is used in the tailstock to establish one end of the mortise axis and the point of the drill bit the other. Center drill first. If you mean squaring the face of the mortise after it is drilled, the pipe is spun on a mandrel inserted in the mortise. This gives the necessary reference to face the end of the shank square to the mortise.
-
- Posts: 3120
- Joined: Sun Sep 02, 2007 4:29 am
- Location: Kansas City, USA
- Contact:
Repairman's perspective:
This issue is my biggest problem when re-stemming hand shaped pipes. A high percentage do not have their mortise aligned with the exterior of the shank. The only recourse is to make the misalignment as camouflaged as possible by "fudging" in other areas to make up the error.
Definitely do your best in this area, guys. getting it right is an excellent channel marker of a carver's overall skill.
This issue is my biggest problem when re-stemming hand shaped pipes. A high percentage do not have their mortise aligned with the exterior of the shank. The only recourse is to make the misalignment as camouflaged as possible by "fudging" in other areas to make up the error.
Definitely do your best in this area, guys. getting it right is an excellent channel marker of a carver's overall skill.
UFOs must be real. There's no other explanation for cats.
Well, let me say that I'm wondering whether this drilling after shaping is for me. The mistakes are compounding. First I drilled the air hole off center, same with the mortise. Hacking my way I finally get to the bowl. Using one of Brad's spade bit I drill a hole first with a regular bit so that it will guide me. With firm steady hand I hold the pipe move it towards the spade. Then all hell brakes loose. Could not hold on well enough to complete the job. Final result a broke bowl, half inch from the top. Thats it for me. Its back to the reliable method drill then shape.
All the best,
Tano
Tano
Are you using the tailstock center as a guide? I've never had a spoon bit grab and buck. You do want to leave some extra meat for corrective shaping, but it sounds like your axis lines are out of whack. Whatever you do, don't give up after one attempt. Perhaps practice with cheap wood, but there's a learning curve no matter how you make pipes. Unless you're making a straight pipe, I'd suggest doing the mortise before the airhole. Try drilling the mortise, then the bowl, then drill the airhole to connect. It sounds risky, but if you use the actual center of the bowl to aim the airhole you're less likely to miss off to the side. Aim a touch low with the airhole, then deepen the bowl just a shade to correct if necessary. If you miss too high, it's pretty hard to recover from that.
Practice makes perfect, I know.
For the air hole I was using a six inch drill bit mounted on one of the motors.
Drilled a test hole first. I've seen pictures of drillers standing in front of the bit pointing at about their belly button. To drill the bowl some suggest drill press, others lathe, either metal or wood. Is there a preferred way to do it?
Thank for the support and tips.
For the air hole I was using a six inch drill bit mounted on one of the motors.
Drilled a test hole first. I've seen pictures of drillers standing in front of the bit pointing at about their belly button. To drill the bowl some suggest drill press, others lathe, either metal or wood. Is there a preferred way to do it?
Thank for the support and tips.
All the best,
Tano
Tano
- KurtHuhn
- Site Admin
- Posts: 5326
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: United States/Rhode Island
Once you've got the pipe roughed in, and your center lines drawn, it's easiest to use a drill press or lathe to be sure everything is lined up. My preference is to use the lathe. That way I can use a dead center in the tailstock and put the intersection of center lines right on that point, and if I drew the lines right, drilling will come out pretty close to spot on.
I've drilled with the bit chucked in a motor as you describe, but typically only for adjustments after the fact.
I've drilled with the bit chucked in a motor as you describe, but typically only for adjustments after the fact.
I've had the same results. Bit hammering from hell, bowl bit going badly off-center, grabbing and breaking, etc. I eventually gave it up as a bad job, and went back to an alternative method of shaping first, not having the working time to waste in fiddling with it for however long it might take to master. My conclusion was that it was obvious I was missing something, but I never could figure out what. I've seen numerous videos where the carver will just hold the stummel in a hand and press it on, and the bit goes in like butter, but in my case it was more - Grab, WHAMM, hammerhammerhammer. I do the airhole and mortise drilling freehand, using centerlines, but I still drill the bowl using various custom vises.Tano wrote:Well, let me say that I'm wondering whether this drilling after shaping is for me. The mistakes are compounding. First I drilled the air hole off center, same with the mortise. Hacking my way I finally get to the bowl. Using one of Brad's spade bit I drill a hole first with a regular bit so that it will guide me. With firm steady hand I hold the pipe move it towards the spade. Then all hell brakes loose. Could not hold on well enough to complete the job. Final result a broke bowl, half inch from the top. Thats it for me. Its back to the reliable method drill then shape.
Happy Smoking,
Trever Talbert
www.talbertpipes.com
My Pipe Blog:
https://talbertpipes.com/category/pipeblog/
My Lizards & Pipes Web Comic:
https://talbertpipes.com/category/lizards/
Trever Talbert
www.talbertpipes.com
My Pipe Blog:
https://talbertpipes.com/category/pipeblog/
My Lizards & Pipes Web Comic:
https://talbertpipes.com/category/lizards/
My 2 cents.Tano wrote:.... Using one of Brad's spade bit I drill a hole first with a regular bit so that it will guide me.
Spade bits tend to be more difficult to control. You might have better control with a reground Silver & Deming bit or a round nose milling bit or a spoon bit.
Last edited by Frank on Sat Jan 05, 2008 4:06 am, edited 1 time in total.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Hmmmm!!
I don't know whether or not that's the problem. When I drill the bowl with any bit, as I get closer to the designated intersection of bowl and air hole I back off completely to check what is happening. When I reinsert the bit thats when the problem occurs. I can' see how anybody can reinsert a bit freehand back into a hole revolving at whatever speed without it not grabbing the wall and creating an imperfection. Its the reinserting several times that makes the whole thing very imprecise. Anyways, thats what the girl said to the sailor.
I don't know whether or not that's the problem. When I drill the bowl with any bit, as I get closer to the designated intersection of bowl and air hole I back off completely to check what is happening. When I reinsert the bit thats when the problem occurs. I can' see how anybody can reinsert a bit freehand back into a hole revolving at whatever speed without it not grabbing the wall and creating an imperfection. Its the reinserting several times that makes the whole thing very imprecise. Anyways, thats what the girl said to the sailor.
All the best,
Tano
Tano
- Tyler
- Site Supporter
- Posts: 2376
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Farmersville, TX
- Contact:
I think he meant Brad's spoon bits, since I believe that is all Brad has offered for sale.Frank wrote:My 2 cents.Tano wrote:.... Using one of Brad's spade bit I drill a hole first with a regular bit so that it will guide me.
Spade bits tend to be more difficult to control. You might have better control with a reground Silver & Deming bit or a round nose milling bit or a spade bit.
Tyler
Tyler Lane Pipes
http://www.tylerlanepipes.com
http://www.tylerlanepipes.com
-
- Posts: 402
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Sweden
- Contact:
Perhaps try replacing the stummel on the bit, apply tailpost center to the depression from previous drilling, hold stummel securely with right hand, turn on lathe with the left. You may already be doing that, but it sounds like you're tilting the stummel slightly to cause the grabbing before the bit can center itself. As with Trever's post a while back, I wonder if your bit has too much material removed. Or perhaps the tailpost is the problem, if it's off center *that* could cause a bind.Tano wrote:Hmmmm!!
I don't know whether or not that's the problem. When I drill the bowl with any bit, as I get closer to the designated intersection of bowl and air hole I back off completely to check what is happening. When I reinsert the bit thats when the problem occurs. I can' see how anybody can reinsert a bit freehand back into a hole revolving at whatever speed without it not grabbing the wall and creating an imperfection. Its the reinserting several times that makes the whole thing very imprecise. Anyways, thats what the girl said to the sailor.