Spoon Bits, photos from the first batch
Spoon Bits, photos from the first batch
Hey guys,
I just got my shipment of spoon bits from Brad. I received them early to give them a test to make sure that they are up to snuff. Good God, are they ever! I have 6 other bits, 1 is of my own manufacture. At first glance, these three bits are superior in craftsmanship and design to anything that I currently own, and may very well be better performers than anything I've ever used. Brad told me that his were cutting the wood off in ribbons. I anticipate the same from mine.
Be encouraged, all who ordered, the bits are good and on their way. Here's a quick photo.
I might be able to snap a few more after I've modified the noses and I'll also try to give you all a shot or two of the work that they are capable of.
Best,
Jeff
I just got my shipment of spoon bits from Brad. I received them early to give them a test to make sure that they are up to snuff. Good God, are they ever! I have 6 other bits, 1 is of my own manufacture. At first glance, these three bits are superior in craftsmanship and design to anything that I currently own, and may very well be better performers than anything I've ever used. Brad told me that his were cutting the wood off in ribbons. I anticipate the same from mine.
Be encouraged, all who ordered, the bits are good and on their way. Here's a quick photo.
I might be able to snap a few more after I've modified the noses and I'll also try to give you all a shot or two of the work that they are capable of.
Best,
Jeff
The side profile looks just like you might expect--the same profile halved.
In terms of grinding it down, you should treat it like grinding tool bits. There's no magic here, just some attention to detail. I've ground 5 others and have had no problem even though I have absolutely no machinist's training. Can you ruin one? Sure, but you'd have to try pretty hard to do so. The idea is to grind the nose down to the profile you want and then to match the rest of the profile to it. It's really not unlike shaping a billiard. Any of us who purchased these bits should be adept enough to handle the operation. Is temper a problem? If you get it too hot, I would imagine that it would be. So, don't get it too hot--just like grinding a tool bit. Do you notice a trend in my post?
Really, I don't mean to be a smartass, but let's not overthink the problem. If you are not confident enough to reshape them leave them as they are or you might be able to pay Brad to reshape them for you.
For what it's worth, I'll try and post the nose of a different spoon bit that I recently reground to give you an idea of what we're talking about. But, seriously, it's not a complex operation, it's common tooling sense.
Good luck gents! I look forward to seeing the wacky creations that chuck liberation creates! And wacky is good!!
Best,
Jeff
In terms of grinding it down, you should treat it like grinding tool bits. There's no magic here, just some attention to detail. I've ground 5 others and have had no problem even though I have absolutely no machinist's training. Can you ruin one? Sure, but you'd have to try pretty hard to do so. The idea is to grind the nose down to the profile you want and then to match the rest of the profile to it. It's really not unlike shaping a billiard. Any of us who purchased these bits should be adept enough to handle the operation. Is temper a problem? If you get it too hot, I would imagine that it would be. So, don't get it too hot--just like grinding a tool bit. Do you notice a trend in my post?
Really, I don't mean to be a smartass, but let's not overthink the problem. If you are not confident enough to reshape them leave them as they are or you might be able to pay Brad to reshape them for you.
For what it's worth, I'll try and post the nose of a different spoon bit that I recently reground to give you an idea of what we're talking about. But, seriously, it's not a complex operation, it's common tooling sense.
Good luck gents! I look forward to seeing the wacky creations that chuck liberation creates! And wacky is good!!
Best,
Jeff
- StephenDownie
- Posts: 228
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Canada
- Contact:
Jeez, it's going to be like Christmas next week! I've got a new IMP meer on the way a new MP3 Player and these bits!. I can't wait to get my hands on them. Thanks again Brad!
Stephen Downie
www.downiepipes.com
www.downiepipes.com
- LexKY_Pipe
- Posts: 875
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Lexington, Kentucky USA
- StephenDownie
- Posts: 228
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Canada
- Contact:
Wohoo! Just got my bits in the mail and they look beautiful! Thanks Brad, I can't wait to shape and break them in this evening.
Stephen Downie
www.downiepipes.com
www.downiepipes.com
Wow, mine arrived today, thanks Brad! These are beautiful!
In terms of shaping the ends. Ok, guys... I know it's like grinding tool bits, but these little gems are perfect, and I don't want to screw them up! And I'm having a difficult time visualizing how best to do this while keeping everything as symetrical as possible. They are perfectly shaped and finished now, and I want them to look just as good when I'm done with the shaping, if possible.
The only idea I've had .... (removed to protect the unsuspecting)
Is that the idea? Any better way to do this? Any help would be greatly appreciated. I'm really excited about getting into this! Thanks again for making this possible, Brad!
In terms of shaping the ends. Ok, guys... I know it's like grinding tool bits, but these little gems are perfect, and I don't want to screw them up! And I'm having a difficult time visualizing how best to do this while keeping everything as symetrical as possible. They are perfectly shaped and finished now, and I want them to look just as good when I'm done with the shaping, if possible.
The only idea I've had .... (removed to protect the unsuspecting)
Is that the idea? Any better way to do this? Any help would be greatly appreciated. I'm really excited about getting into this! Thanks again for making this possible, Brad!
Last edited by sethile on Sat Jun 16, 2007 12:09 am, edited 1 time in total.
Scott E. Thile
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Scott,
I highly suggest that you do not do as you wrote. This will end up in a very uneven grind and probably a rounded cutting edge. I know that it's difficult ot visualize at first, but think of reshaping spade bits--now do it in 3D. The way I do it is by grinding the profile first while placing the flat part of the bit on the grinder rest. Then matching the rest of the profile to it will finish the job. You'll probably be altering only the tip--maybe 1/4"--and therefore you needn't worry too much about ruining the fine profile Brad created.
Best,
jeff
I highly suggest that you do not do as you wrote. This will end up in a very uneven grind and probably a rounded cutting edge. I know that it's difficult ot visualize at first, but think of reshaping spade bits--now do it in 3D. The way I do it is by grinding the profile first while placing the flat part of the bit on the grinder rest. Then matching the rest of the profile to it will finish the job. You'll probably be altering only the tip--maybe 1/4"--and therefore you needn't worry too much about ruining the fine profile Brad created.
Best,
jeff
- staffwalker
- Site Supporter
- Posts: 391
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: USA, texas
Thanks Jeff! You saved me! I knew it was risky not to have a better take on this. I really appreciate your extra advice. I will edit my idea out of my post before someone ruin's theirs with it! I'll give your suggestion a careful try. It's hard to imagine being able to keep the symetry exact, and they're so perfect nowjeff wrote:Scott,
I highly suggest that you do not do as you wrote. This will end up in a very uneven grind and probably a rounded cutting edge. ....
Scott E. Thile
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Don't drop them.jbacon wrote: just one question - what is the best way to keep them sharp
Sharpening should not need to occur very often. As hobbiests you *may* need to sharpen them once a year, if that. All you need to do us run the flat part of the bit across a diamond hone. Never, NEVER, sharpen from the rounded edge. That will remove the cutting edge completely from contacting the wood.
C'mon now. Let's stop asking questions and start posting pictures of your first efforts!
thanks jeff
just two more questions and i will be set. I am using the jet bd-920
what rpms do you use to drill on your jet- 130 is the lowest rmp setting
can you go to slow. And also do you start w/ a pilot hole john crosby said
he uses a 5/32 and then a 3/8 w/a rounded edge
thanks for all your patience and help
jim
just two more questions and i will be set. I am using the jet bd-920
what rpms do you use to drill on your jet- 130 is the lowest rmp setting
can you go to slow. And also do you start w/ a pilot hole john crosby said
he uses a 5/32 and then a 3/8 w/a rounded edge
thanks for all your patience and help
jim