Chuck Question
Chuck Question
Hello
Was looking on google books and found this. https://books.google.no/books?id=nCcDAAAAMBAJ&hl=no on page 181. There is a drawing of a chuck this guy used for several thousands pipe, but would it be anything to use today?
Sent from my iPhone using Tapatalk
Was looking on google books and found this. https://books.google.no/books?id=nCcDAAAAMBAJ&hl=no on page 181. There is a drawing of a chuck this guy used for several thousands pipe, but would it be anything to use today?
Sent from my iPhone using Tapatalk
- baweaverpipes
- The Awesomer
- Posts: 947
- Joined: Tue Dec 19, 2006 8:07 am
- Location: Franklin, Tennessee
- Contact:
Re: Chuck Question
Theoretically, but why use dated tooling when there is better. Try Trent Rudat, he makes fantastic two jaw chucks.
Re: Chuck Question
"Can I use it?" and "Is it any good?" are very different questions.
That looks to be a slight modification of a 4 jaw chuck. Easier to buy a wood-turning chuck like a Oneway and get some jaws for it and screw them on.
That looks to be a slight modification of a 4 jaw chuck. Easier to buy a wood-turning chuck like a Oneway and get some jaws for it and screw them on.
ALL YOUR PIPE ARE BELONG TO US!
Re: Chuck Question
Thanks for answers! I am not that good in English, but what I meant was, would it be safe to use in your opinion?
Re: Chuck Question
With any chuck, the biggest thing is probably if you can get the block nice and square so it sits well. That makes it safe. If it's lumpy, it's hard to get ahold of.
ALL YOUR PIPE ARE BELONG TO US!
Re: Chuck Question
That stem Chuck is cool I got one it still works great Albeit most people didn't have different size lathes.
Same ca be done on a mini lathe
Same ca be done on a mini lathe
"I never knew how empty was my soul untill it was filled" Arthur
http://www.clarkpipes.com
http://www.clarkpipes.com
Re: Chuck Question
I checked out your link, very entertaining. I marvel that you found this article.
I note that it is the November 1941 issue, and that the lathe was described as 'ancient' 75 years ago.
The basic mechanism used to turn the stummel is the same as pipe turners use today but the face plate used is different and appears to be somewhat less secure than the tower jaws on a 4 jaw chuck used these days.
Of course a chuck and tower jaws can set you back hundreds of dollars, while the modified face plate could cost considerably less if you have the materials and machining skills to build it.
If you go that route, I would recommend that you wear a face shield while using such a mechanism, because I can almost guarantee that you will have a stummel come loose and fly off during turning.
It will work and if obtaining a modern chuck and tower jaws is beyond your means at this time, then be careful with it.
Good luck
DocAitch
I note that it is the November 1941 issue, and that the lathe was described as 'ancient' 75 years ago.
The basic mechanism used to turn the stummel is the same as pipe turners use today but the face plate used is different and appears to be somewhat less secure than the tower jaws on a 4 jaw chuck used these days.
Of course a chuck and tower jaws can set you back hundreds of dollars, while the modified face plate could cost considerably less if you have the materials and machining skills to build it.
If you go that route, I would recommend that you wear a face shield while using such a mechanism, because I can almost guarantee that you will have a stummel come loose and fly off during turning.
It will work and if obtaining a modern chuck and tower jaws is beyond your means at this time, then be careful with it.
Good luck
DocAitch
"Hettinger, if you stamp 'hand made' on a dog turd, some one will buy it."
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
-Charles Hollyday, pipe maker, reluctant mentor, and curmudgeon
" Never show an idiot an unfinished pipe!"- same guy
- NevadaBlue
- Posts: 18
- Joined: Tue Jul 07, 2015 12:33 am
Re: Chuck Question
I made the article into a PDF to make it easier to use.
Link:
https://www.dropbox.com/s/eee02zwy93rrr ... g.pdf?dl=0
Link:
https://www.dropbox.com/s/eee02zwy93rrr ... g.pdf?dl=0
...
Ken
Ken
-
- Posts: 162
- Joined: Thu Feb 14, 2013 2:40 am
- Location: Abilene TX or Ruidoso NM
Re: Chuck Question
Instead of making a chuck, convert the same thing to a vise for the drill press. Then use the drill press as a mill to bore out the stummel and drill the airway. Mounted in a 2 way cross slide vise and you have a basic milling machine setup. That way you don't have to wonder when the blank will break loose and slap you upside the head.
Re: Chuck Question
As George will attest you need a really good drill press to do a good work on drilling pipes, most have too much slop in the spindle and too little travel.
-
- Posts: 162
- Joined: Thu Feb 14, 2013 2:40 am
- Location: Abilene TX or Ruidoso NM
Re: Chuck Question
True, but sometimes the sloppy drill press is because of operator ignorance.caskwith wrote:As George will attest you need a really good drill press to do a good work on drilling pipes, most have too much slop in the spindle and too little travel.
A tune up of the drill press might help. http://www.rvplane.com/pdf/drill_press_tune-up.pdf
- NevadaBlue
- Posts: 18
- Joined: Tue Jul 07, 2015 12:33 am
Re: Chuck Question
It would be a pretty sad drill press that had too much slop in the spindle to drill a hole in wood.
...
Ken
Ken
Re: Chuck Question
There's a big difference between drilling a hole and drilling an accurate hole. It's the mortise hole and face really that I am talking about, chamber and airway not so important.
-
- Posts: 162
- Joined: Thu Feb 14, 2013 2:40 am
- Location: Abilene TX or Ruidoso NM
Re: Chuck Question
This set up here viewtopic.php?f=9&t=11115 Is just another version of the chuck/vise that is in the quoted article.
A drill press is a vertical lathe without a tool rest, and a lathe is a horizontal drill press with a tool rest.
A drill press is a vertical lathe without a tool rest, and a lathe is a horizontal drill press with a tool rest.