Finally restoring my Craftsman 109
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Finally restoring my Craftsman 109
So I know its teeny tiny, but it is going to be dedicated to stems. For younz that follow me on IG you have seen some of these pictures already.
Here is a before picture from when I got this lathe in July. It's been sitting in a box under my workbench since then.
Tear down begins
All painted and ready for reassembly tomorrow.
The ways are in great shape and just needed a touch with some wd40 and a scotchbright pad. Luckily the rust wasn't too deep on the feet. And so far I have about $150 into it so it was crazy cheap. What's bad is a chuck for it is going to cost me more than that
Here is a before picture from when I got this lathe in July. It's been sitting in a box under my workbench since then.
Tear down begins
All painted and ready for reassembly tomorrow.
The ways are in great shape and just needed a touch with some wd40 and a scotchbright pad. Luckily the rust wasn't too deep on the feet. And so far I have about $150 into it so it was crazy cheap. What's bad is a chuck for it is going to cost me more than that
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
Re: Finally restoring my Craftsman 109
Looks like a fun project, Scottie! Should make a great little lathe for stem work.... Bet it's way better, and is certainly much cooler than the little 7x12 Chinese lathe I had in the beginning for stem work.
Scott E. Thile
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Collector, smoker, and aspiring pipemaker.
http://sethilepipes.com
Sysop: http://pipedia.org
---------------------
Re: Finally restoring my Craftsman 109
All you need is a 3 or 4 jaw chuck for stems, you can pick up a chinese one pretty cheap on Ebay.
I started using a 4 jaw chuck for stems and like it better than the 3 jaw I have always used.
I started using a 4 jaw chuck for stems and like it better than the 3 jaw I have always used.
Ryan Alden
http://www.aldenpipes.com
http://www.aldenpipes.com
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
Thanks Scott. I think it is a 6x16, but I really don't remember the bed length. Its super heavy for its size and should really be rigid.
The problem with getting a chuck is the adapter I need. The spindle is 1/2" x 20 tpi. I keep an eye out on ebay for chucks and haven't run across one that has that thread that's not rusted. I am actually thinking about getting an adapter from Oneway and putting my Oneway I use for stems on it. It would only cost me $75 that way.
The problem with getting a chuck is the adapter I need. The spindle is 1/2" x 20 tpi. I keep an eye out on ebay for chucks and haven't run across one that has that thread that's not rusted. I am actually thinking about getting an adapter from Oneway and putting my Oneway I use for stems on it. It would only cost me $75 that way.
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
Re: Finally restoring my Craftsman 109
before you spend out for a chuck and tooling, get yourself a Dial indicator and check that the shaft and spindle nose are not bent or anything, be a real shame to buy a chuck and then find it won't run true. Bent shaft is about the only bit of lathe mis-alignment that you can't fix.
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
No worries, Chris. I have a brand new spindle for it. Before I bought it I found a place that sells parts for the 109 and nothing else (the reason I decided to go with this model). He hooked me up with a new spindle. I bought the lathe off ebay for $150 and then the seller sent me an email that the spindle was bent....I ended up getting it for $75.00.
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
-
- Posts: 363
- Joined: Thu Feb 13, 2014 3:36 pm
- Location: Colorado Springs, Co
Re: Finally restoring my Craftsman 109
Scotties please remember to post pics of it complete.
Sent from my banana phone.
Sent from my banana phone.
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
NO...and don't ever ask again!!!! Sorry, thought one of my kids was asking for something for the 800th time in 2 minutes.Ccoolee wrote:Scotties please remember to post pics of it complete.
I sure will. I got the headstock cover back on the bed last night. I might try to get the headstock put back together this afternoon. We'll see how the day goes.
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
- wisemanpipes
- Posts: 528
- Joined: Wed Jan 16, 2013 12:11 pm
- Location: Guelph, Ontario
Re: Finally restoring my Craftsman 109
this is SOO awesome. I really want to restore a lathe one day soon and im a bit of a tool junky, so itd be up my alley.
as scott said, should be primo for stems. nice and heavy steel.
good luck on reassembly!
hopefully you don't have extra pieces at the end like I do when I reassemble stuff. famous last words "where the hell did this come from?!"
Evan
as scott said, should be primo for stems. nice and heavy steel.
good luck on reassembly!
hopefully you don't have extra pieces at the end like I do when I reassemble stuff. famous last words "where the hell did this come from?!"
Evan
Re: Finally restoring my Craftsman 109
scotties22 wrote:No worries, Chris. I have a brand new spindle for it. Before I bought it I found a place that sells parts for the 109 and nothing else (the reason I decided to go with this model). He hooked me up with a new spindle. I bought the lathe off ebay for $150 and then the seller sent me an email that the spindle was bent....I ended up getting it for $75.00.
Ahh great stuff!
-
- Posts: 363
- Joined: Thu Feb 13, 2014 3:36 pm
- Location: Colorado Springs, Co
Re: Finally restoring my Craftsman 109
Alright, I'll show off my immaturity. Ever see that episode of family guy.scotties22 wrote: NO...and don't ever ask again!!!! Sorry, thought one of my kids was asking for something for the 800th time in 2 minutes. .
Mom, mom, mom, mommy, mother, Lois, Lois, mom mommy.
Ha my favorite thanks
Sent from my banana phone.
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
My mom was a real smart ass when it came to that. However many times I said her name was how many times she said my name back
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
-
- Posts: 162
- Joined: Thu Feb 14, 2013 2:40 am
- Location: Abilene TX or Ruidoso NM
Re: Finally restoring my Craftsman 109
Do you have a motor? If not you might think about looking at the industrial sewing machine motors, they are servo motors that are variable speed and reversible. On my wood lathe I have a 3/4 Consew, not one of the best, but it works for me, on my next lathe conversion I plan on using a Sewquiet 5000, it supposed to have better torque in the slower speeds. But it will cost me a little more at $199 on Amazon.
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
I have an extra motor for my Rikon wood lathe I am going to use. Going to build (or buy) a countershaft for it.
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
Re: Finally restoring my Craftsman 109
Neat little lathes they are, I have one just like it....err, mines all there though. Craftsman 109.2063
You can pick up the original 4 jaw chucks pretty easy and cheaply on eBay if you keep an eye out for under $100.
Looks like you'll need some other parts as well. If you haven't already check this site out, it's all about those lathes and parts.
http://www.homeshopsupply.com/index.html
I have a copy of the owners manual if you need it.
You can pick up the original 4 jaw chucks pretty easy and cheaply on eBay if you keep an eye out for under $100.
Looks like you'll need some other parts as well. If you haven't already check this site out, it's all about those lathes and parts.
http://www.homeshopsupply.com/index.html
I have a copy of the owners manual if you need it.
rdpipes.briar.club
-
- Posts: 1767
- Joined: Mon Jun 11, 2012 9:43 pm
- Location: Missouri
- Contact:
Re: Finally restoring my Craftsman 109
Yeah, Bill is a great guy. I bought the new spindle and a few other things from him. Last time I talked to him he wasn't doing too well. I saw on his website that he is working a bit when he can. If I had the money I would buy his inventory and take over for him.RDPowell wrote:Neat little lathes they are, I have one just like it....err, mines all there though. Craftsman 109.2063
You can pick up the original 4 jaw chucks pretty easy and cheaply on eBay if you keep an eye out for under $100.
Looks like you'll need some other parts as well. If you haven't already check this site out, it's all about those lathes and parts.
http://www.homeshopsupply.com/index.html
I have a copy of the owners manual if you need it.
If I have any questions guess I know who to ask
Am I Calamity Jane or Annie Oakley??...depends on the day.
www.ladybriar.com
www.ladybriar.com
Re: Finally restoring my Craftsman 109
Sure! But I can't guarantee they'll be the right answersscotties22 wrote:Yeah, Bill is a great guy. I bought the new spindle and a few other things from him. Last time I talked to him he wasn't doing too well. I saw on his website that he is working a bit when he can. If I had the money I would buy his inventory and take over for him.RDPowell wrote:Neat little lathes they are, I have one just like it....err, mines all there though. Craftsman 109.2063
You can pick up the original 4 jaw chucks pretty easy and cheaply on eBay if you keep an eye out for under $100.
Looks like you'll need some other parts as well. If you haven't already check this site out, it's all about those lathes and parts.
http://www.homeshopsupply.com/index.html
I have a copy of the owners manual if you need it.
If I have any questions guess I know who to ask
rdpipes.briar.club
Re: Finally restoring my Craftsman 109
Cute lathe, Scottie! If I were able to get something like that for a price like that, I would have been on it in a flash.