Want to show you work to the world? Want a place to post photos of your work and solicit the opinions of those that have gone before you? Post your work here.
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Nov 28, 2012 12:25 pm
Last edited by
jmoss on Wed Nov 28, 2012 12:52 pm, edited 1 time in total.
kkendall
Posts: 472 Joined: Thu Mar 01, 2007 1:15 pm
Location: Phoenix, AZ
Contact:
Post
by kkendall » Wed Nov 28, 2012 12:47 pm
You might want to take a few minutes to resize those. They're WAY to big!
WCannoy
Posts: 542 Joined: Thu Nov 15, 2012 6:58 pm
Location: Lakeland, Florida
Contact:
Post
by WCannoy » Wed Nov 28, 2012 12:52 pm
They all look better than my first pipe looked!
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Nov 28, 2012 12:54 pm
kkendall wrote: You might want to take a few minutes to resize those. They're WAY to big!
Sorry about that, I realised that after I had submitted the message. I thought they would be automatically downsized. My bad.
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Nov 28, 2012 1:00 pm
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Nov 28, 2012 1:13 pm
WCannoy wrote: They all look better than my first pipe looked!
Thank you...Your site has problem does not open
WCannoy
Posts: 542 Joined: Thu Nov 15, 2012 6:58 pm
Location: Lakeland, Florida
Contact:
Post
by WCannoy » Wed Nov 28, 2012 1:48 pm
jmoss wrote:
Thank you...Your site has problem does not open
Hmmm... Seems to be working fine for me. Anyone else having a problem with it?
There's really nothing on there yet anyway...
the rev
Posts: 737 Joined: Wed Oct 01, 2008 1:42 pm
Location: long beach CA
Contact:
Post
by the rev » Wed Nov 28, 2012 1:55 pm
works fine for me
rev
"but rev, isn't smoking a sin?"
well I suppose if one were to smoke to excess it would be a sin
"but what would be smoking to excess?"
Why smoking two pipes at once of course
d.huber
Posts: 2691 Joined: Mon Dec 12, 2011 9:28 pm
Location: Durham, NC
Contact:
Post
by d.huber » Wed Nov 28, 2012 2:05 pm
Workin' for me, too.
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Nov 28, 2012 2:09 pm
WCannoy wrote: jmoss wrote:
Thank you...Your site has problem does not open
Hmmm... Seems to be working fine for me. Anyone else having a problem with it?
There's really nothing on there yet anyway...
Now it s fine ..
LexKY_Pipe
Posts: 875 Joined: Thu Nov 23, 2006 8:00 pm
Location: Lexington, Kentucky USA
Post
by LexKY_Pipe » Sat Dec 01, 2012 6:43 pm
Good start. Work hard on your shank/stem joint.
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Sun Dec 02, 2012 8:58 am
LexKY_Pipe wrote: Good start. Work hard on your shank/stem joint.
Thank you for the tip...
Ocelot55
Posts: 1639 Joined: Thu Nov 10, 2011 12:31 pm
Location: Columbus, OH
Contact:
Post
by Ocelot55 » Sun Dec 02, 2012 1:57 pm
Don't be afraid to take off a lot more meat where the shank and the bowl meet. That area needs to be well defined.
(note: this is probably the most common tip for new pipe makers)
jmoss
Posts: 84 Joined: Sun Sep 30, 2012 9:51 am
Post
by jmoss » Wed Jun 05, 2013 9:40 am
Ocelot55 wrote: Don't be afraid to take off a lot more meat where the shank and the bowl meet. That area needs to be well defined.
(note: this is probably the most common tip for new pipe makers)
Thank you very much guys...