My lathe is about 0.5mm out. How do you shimmy a lathe, first of all, and how do you measure exactly by how much it is out?
Any help would be appreciated!
Lathe problems
What is out and where? In relation to what - The bed, the tailstock, the centre line - The X-axis or Y-axis? Where on the lathe do you want to shim it? What make of lathe? Need more specific info.
You probably need something like this: http://www.use-enco.com/CGI/INPDFF?PMPAGE=355Charl wrote:...and how do you measure exactly by how much it is out?
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Different lathes may require a different remedy. This doc touches on quite a few problems and possible repairs.
http://jlrodgers.com/pdf/lathe_alignment.pdf
Hope it helps somewhat.
http://jlrodgers.com/pdf/lathe_alignment.pdf
Hope it helps somewhat.
Sorry for being vague , had a very rough Monday.
It is a very old Eglish model (still have one leather V belt) and the tailstock is a bit low in relation to the headstock. I don't know much about metal lathes, but I would suppose that you need to somehow raise the tailstock by inserting something between it and the bed?
Will try and get a photo tomorrow when I'm not half asleep
It is a very old Eglish model (still have one leather V belt) and the tailstock is a bit low in relation to the headstock. I don't know much about metal lathes, but I would suppose that you need to somehow raise the tailstock by inserting something between it and the bed?
Will try and get a photo tomorrow when I'm not half asleep
Get an assortment of Shim Stock like this and cut to size with scissors: http://www.use-enco.com/CGI/INSRIT?PMAK ... PG=INLMK32
The other alternative is to have the foot/base of the tailstock built up (with weld?) then ground down to the correct height. This would probably require a professional machine shop, because the foot/base of the tailstock has to be perfectly parallel to the centre line of the tailstock.
The easiest way to check spindle/tailstock alignment is to put a dead centre in both the spindle and tailstock. Place a stiffish piece of paper between them and run the tailstock centre almost up to the spindle centre so that both points are just supporting the paper. When the paper remains perfectly perpendicular to the centre axis, the spindle and tailstock are aligned.
The other alternative is to have the foot/base of the tailstock built up (with weld?) then ground down to the correct height. This would probably require a professional machine shop, because the foot/base of the tailstock has to be perfectly parallel to the centre line of the tailstock.
The easiest way to check spindle/tailstock alignment is to put a dead centre in both the spindle and tailstock. Place a stiffish piece of paper between them and run the tailstock centre almost up to the spindle centre so that both points are just supporting the paper. When the paper remains perfectly perpendicular to the centre axis, the spindle and tailstock are aligned.
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
His solution of shimming just one corner of the head or tailstock could result in introducing more runout. You need to shim one entire side of either the head or tailstock to keep the centre line running dead straight through the spindle to the end of the tailstock quill.ckr wrote:This doc touches on quite a few problems and possible repairs. http://jlrodgers.com/pdf/lathe_alignment.pdf
Regards,
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett
Frank.
------------------
Grouch Happens!
People usually get the gods they deserve - Terry Pratchett