Hi,
I just signed up last week. I've been reading the posts. Lots of good information getting exchanged here. I have photos of two of my latest (if I get this picture posting thing right). Honest evaluations are welcome.
These are my first pipes with good quality straight grain briar. The top one has a natural edge although it doesn't show in this pic. I've made just over 50 pipes since I started last October. It's lots of fun and challenging as well.
Dave
Hiway's Pipes
- Tyler
- Site Supporter
- Posts: 2376
- Joined: Thu Nov 23, 2006 8:00 pm
- Location: Farmersville, TX
- Contact:
hiway,
Welcome to the group!
I'll add a few comments on your pipes. Let me begin by saying that they both nice looking pipes!
My main comment is the same for both pipes. The bottom line of the pipes do not have a continuous line. Both are such nice shapes that I think they woulc be quite good with this little tweak. The top pipe is better in this regard than the bottom one, but even the top one drops down to have a small pooch on the bottom of the bowl. I recognise that this move allows for more briar at the base of the bowl, but I do not think it is worth it unless the pipe is severely over-drilled and you have no choice. Just keeping the lline of the shank all the way through the bottom of the bowl would make this much more elegant, IMO.
As for the second pipe there are two line changes along the bottom line. The pooch is there on the bottom of the bowl, as with the first pipe, and there is then a constant diameter for an inch or two before a steep taper just before the bend. Again, I recommend a constant line along the bottom. Also, for this pipe, as someone else suggested, I think the bend is just a fraction too much.
Clearly though, those are nice pipes. I am picking rather fine nits, but I am doing it because that is what I would want done for me. And the point of the board is for us all to get better at this craft!
Good job.
Tyler
Welcome to the group!
I'll add a few comments on your pipes. Let me begin by saying that they both nice looking pipes!
My main comment is the same for both pipes. The bottom line of the pipes do not have a continuous line. Both are such nice shapes that I think they woulc be quite good with this little tweak. The top pipe is better in this regard than the bottom one, but even the top one drops down to have a small pooch on the bottom of the bowl. I recognise that this move allows for more briar at the base of the bowl, but I do not think it is worth it unless the pipe is severely over-drilled and you have no choice. Just keeping the lline of the shank all the way through the bottom of the bowl would make this much more elegant, IMO.
As for the second pipe there are two line changes along the bottom line. The pooch is there on the bottom of the bowl, as with the first pipe, and there is then a constant diameter for an inch or two before a steep taper just before the bend. Again, I recommend a constant line along the bottom. Also, for this pipe, as someone else suggested, I think the bend is just a fraction too much.
Clearly though, those are nice pipes. I am picking rather fine nits, but I am doing it because that is what I would want done for me. And the point of the board is for us all to get better at this craft!
Good job.
Tyler
Tyler Lane Pipes
http://www.tylerlanepipes.com
http://www.tylerlanepipes.com
Thanks for the feedback everyone.
It's great to have some strong feedback from the makers point of view. I'm looking forward to many interesting posts.
Dave
I tend to build up layers so I started with light tan for several coats then added a drop or two or oxblood then finished with a couple of drops of medium brown. When mixing I use a shot glass and start with an eyedropper full of the base (usually the lightest) color. I keep applying stain until the stummel is saturated. I use Feibing alcohol based leather dyes.What color stain is that on the top one?
Yes, it appears so. In real life it is proportionate to the top of the bowl. I have just learned something about photographing pipes. Because of the angle I shot the picutre at it looks like it is bent too far.I like the forward cant of the bowl on the second pipe alot. Although the stem bend seems just a bit off
I agree, it's not my favorite either. The size and shape of the block and the grain pattern dictated it.I don't care for the first one, that's just personal taste, never have cared for that type of shape.
Very slightly forward but not as much as the outside of the bowl. When I do this shape again I will use a more tapered bit as I ended up with slightly less wood than I like around the bottom front of the bowl.Is the bowl drilled vertically or is it drilled with a forward cant
True enough. I'm still working on that. They are not overdrilled but I will have more wood to work with if I drill the tobacco hole shallower and angle the draught hole slightly upward.The bottom line of the pipes do not have a continuous line.
It's great to have some strong feedback from the makers point of view. I'm looking forward to many interesting posts.
Dave